中控华运 | 产 品 中 心
18877
page-template-default,page,page-id-18877,ajax_fade,page_not_loaded,,qode-theme-ver-10.1.1,wpb-js-composer js-comp-ver-5.0.1,vc_responsive
 

产 品 中 心

Easypalok 806

Easypalok 806指纹识别挂锁操作说明 

登录指纹:

轻按指纹窗口——蓝灯闪烁(表示进入登录状态)——按压手指,见绿灯亮移开手指;然后再按压手指,绿灯亮;共三次循环后,登录完成——自动关机。本产品最多可以登录十枚指纹,最早登录的两枚指纹具有管理权限(简称“优先指纹”),它们具有追加或删除其他指纹的权限。追加指纹时,由优先指纹之一先验证开锁后,继续按压指纹窗口3秒以上,绿灯闪烁,移开手指后蓝灯闪烁(进入登录状态),此时让需要新增登录的手指,执行上述登录操作,即可完成指纹追加登录。

验证开锁: 已经登录过的手指,直接按压指纹窗口,验证成功即可开锁,验证失败可以继续尝试(最多七次后关机)。

删除指纹: 在锁闭状态下,将U型锁钩往下按压到底(虽然只能按下去一点点位置),用任意手指轻触指纹窗口进入删除模式(红蓝色灯常亮),然后用优先手指按压住指纹窗口不松开,待红灯闪烁(进入待删除状态)3秒后,绿灯常亮表示删除成功。若红灯闪烁绿灯常亮之前移开手指,则删除终止,关机。优先指纹执行上述操作后,除了前两个优先指纹外的其他指纹全部被一次性清除。若连续执行两次上述删除操作,则所有指纹全部删除(包括两个优先指纹)。

低电压报警及充电:

当系统侦测到电池容量较低时,若触碰指纹窗口,黄色灯闪烁报警。此时还可以正常开锁。从第一次黄色灯闪烁时计算,还可以继续使用50次左右(仅仅开锁)。低电压报警后,请及时充电。若完全没电不能开锁时,请使用充电宝等外接电源,USB接口连接,可马上验证指纹开锁。

充电时,请拨开USB胶塞,插入USB线,连接平常使用的手机充电适配器或连接PC、平板电脑等即可。在充电过程中红灯闪烁,大约充电60分钟后,指示灯变绿,表示充电完成。


Easypalok 806 Operation Guidance

① Fingerprint(FP) Enrollment: Touch the fingerprint window to start, blue LED blink means FP data empty and anyone can register. Press a finger on the window and remove when green LED shows, then press the same finger again and remove until three pressing and green LED shows– an enrollment ends and the lock turn down automatically.

At most ten fingerprints can be enrolled in this lock. The first two registered fingers are privileges—they can be used to add or delete other fingerprints. When add new fingers, one of the first two enrolled finger must be verified first, after verification the same finger keeps pressing 3 more seconds till the green LED blink, then remove the finger and the blue LED blink which means the enrollment mode, using a new finger to conduct the above enrollment operation, that will add the new fingerprint into the lock storage.

② Verification and unlock: Press an enrolled finger on the window if it’s verified then the green LED solid and it unlock, if failed the red LED shows, please try again with a more careful press —there would be 6 more tries before the lock turn off.

Fingerprint Deletion: When it locked, press down the U-type shackle to its lowest position (just a little bit down) and touch the windows with any finger to see blue and red LED , that means the deletion mode, then loosen the shackle and use a privilege finger to press FP window, red LED solid, keeps pressing to see red LED blinking three times then green LED solid indicates all fingerprints except the first two (privilege fingers) be deleted. Removing finger while red LED blinking would abort the deletion. Repeat this deleting operation immediately will delete the two privilege fingerprints– the lock would be empty as default when out of factory.

Low power alert and Recharge: When the system detects low power the yellow LED will blink if touch the window.  From the first time to see yellow blink you can conduct about 50 more verifications and unlock (after that the lock will lose all power). You can recharge the battery of the lock via USB link to PC/tablet or any mobile phone charger when lower power prompt. If totally out of power, you can link the lock to a charge pal or other portable power supply to do the verification and unlock, and then recharge it.

When connect and recharge, open the silicone USB plug cover, insert the USB cable and link to any PC/tablet or charge pal. Red LED is blinking while charge, it takes about 60 minutes to charge the battery from empty to full. The green LED indicates that the charging is completed.

Easypalok 316指纹挂锁

Easypalok 316指纹识别挂锁操作说明 

登录指纹:

轻按指纹窗口——蓝灯闪烁(表示进入登录状态)——按压手指,见绿灯亮移开手指;然后再按压手指,绿灯亮;共三次循环后,登录完成——自动关机。本产品最多可以登录十枚指纹,最早登录的两枚指纹具有管理权限(简称“优先指纹”),它们具有追加或删除其他指纹的权限。追加指纹时,由优先指纹之一先验证开锁后,继续按压指纹窗口3秒以上,绿灯闪烁,移开手指后蓝灯闪烁(进入登录状态),此时让需要新增登录的手指,执行上述登录操作,即可完成指纹追加登录。

验证开锁: 已经登录过的手指,直接按压指纹窗口,验证成功即可开锁,验证失败可以继续尝试(最多七次后关机)。

上锁:将钢丝绳末端插进锁孔,蓝色亮则上锁成功;

删除指纹: 按压左侧硅胶垫(建议用指甲或其他尖锐物按压焦点中心位置,听到滴答声)同时轻按指纹窗口,进入删除模式(红色灯常亮),用优先手指按压住指纹窗口不松开,待红灯闪烁(进入待删除状态)3秒后,绿灯常亮表示删除成功。若红灯闪烁绿灯常亮之前移开手指,则删除终止,关机。优先指纹执行上述操作后,除了前两个优先指纹外的其他指纹全部被一次性清除。若优先指纹连续执行两次上述删除操作,则指纹全部删除(包括两个优先指纹)。

低电压报警及充电:

当系统侦测到电池容量较低时,若触碰指纹窗口,黄色灯闪烁报警。此时还可以正常开锁。从第一次黄色灯闪烁时计算,还可以继续使用50次左右(仅仅开锁)。低电压报警后,请及时充电。若完全没电不能开锁时,请使用充电宝等外接电源,USB接口连接,可马上验证指纹开锁。

充电时,请拨开USB胶塞,插入USB线,连接平常使用的手机充电适配器或连接PC、平板电脑等即可。在充电过程中红灯闪烁,大约充电60分钟后,指示灯变绿,表示充电完成。


Easypalok 316 Operation Guidance

① Fingerprint(FP) Enrollment: Touch the fingerprint window to start, blue LED blink means FP data empty and anyone can register. Press a finger on the window and remove when green LED shows, then press the same finger again and remove until three pressing and green LED shows — an enrollment ends and the lock turn down automatically.

At most ten fingers can be enrolled in this lock. The first two registered fingers are privileges—they can be used to add or delete other fingerprints. When add new fingerprints, one of the first two enrolled finger must be verified first, after verification the same finger keeps pressing the window 3 more seconds till the green LED blink, then remove the finger and the blue LED will blink, that means the enrollment begin, using a new finger to conduct the above enrollment operation, that will add the new fingerprint into the lock storage.

② Verification and unlock: Press an enrolled finger on the FP window if it’s verified then the green LED solid and it unlock, if failed the red LED shows, please try again with a more careful press —there would be 6 more tries before the lock turn off.

 Lock up: to lock it up just insert the steel-cord belt into the hole, blue LED shows the successful lockup.

Fingerprint Deletion:  Whatever locked or unlocked, press the silicone rubber button (please press the center using fingernail or other sharp stuff to hear a ticktack) on the side of the lock and touch the FP window simultaneously, the red LED solid means the deletion mode, then using a privilege finger to press FP window until red LED blinks, hold on for 3 seconds and then green LED solid indicates all fingers except the first two (privilege fingers) be deleted. Removing finger while red LED blinking would abort the deletion. Repeat this deleting operation immediately will delete the two privilege fingerprints– the lock would be empty as default when out of factory.

⑤ Low power alert and Recharge: If the system detects low power the yellow LED will blink when touch the window.  From the first time to see yellow LED blink you can conduct about 50 more verifications and unlock (after that the lock will lose all power). You can recharge the battery of the lock via USB link to PC/tablet or any mobile phone charger when lower power prompt. If totally out of power, you can link the lock to a charge pal or other portable power supply to do the verification and unlock, and then recharge it.

When connect or recharge, open the silicone USB plug cover, insert the USB cable and link to any PC/tablet or charge pal. Red LED blinks while charging, it takes about 60 minutes to charge the battery from empty to full. The green LED solid indicates charging completed.

ZKM 100电容式指纹采集模组

ZKM 100电容式指纹模组规格书下载码

ZKM101 电容式指纹模组

ZKM 101 电容式指纹识别模组规格书下载码

指纹ID卡

 

特点:

1)体积小、集成密度高:一卡集成指纹识别射频卡,指纹采集、存储、识别、射频卡控制全部在自由模组或卡上完成

2) 算法优化、低功耗、创新工艺

3) 完整的兼容性

4) 信用卡级安全:捕捉、存储、匹配卡片、便携式存储模板、隐私保护

5) HW加密:编码和数据的芯片级加密

6) 更高的安全性:与常规访问控制相比,特殊模式使系统更加健壮

7) 自有技术和知识产权

应用:

信息安全方面:

1)通过配套的USB充电器与电脑连接,进行指纹验证,对电脑、数据和软件加密

2) 通过蓝牙无线连接到计算机和移动设备,进行指纹验证

3) 可以用作密匙生成和传送加密器,以及指纹U盘。

4) 指纹验证和射频识别卡的微型组合

ZK302_192指纹识别芯片

 

ZK302_192指纹识别芯片是一款具有高灵敏度的电容按压式指纹识别 IC。

可采用表面平坦化注塑封装技术,可支持玻璃盖板,可灵活切割,结构适应性强,具有优越的抗静电、耐磨损及耐腐蚀等特性。
结合优秀的指纹识别算法以及成熟的应用软件配套,可为嵌入式应用提供优秀的使用体验。

ZK601_360 面阵式指纹传感器

 

1)ZK601_360面阵式指纹传感器采用行业领先的主动式指纹采集原理,内置8-bit ADC,提供并口与 SPI 串口两种模式。

2)传感器表面采用7H以上的coating材料,防止指纹芯片和手指的直接接触,能承受100万次以上的擦刮。
3)ZK601_360传感器提供每个点256阶灰度,由于采用了主动式原理, 相比被动式提供了5倍的图像增强。面阵共360×256个像素点一次就可以完整采集指纹。
4)芯片采用了特殊的coating材料,ESD保护可达15KV,符合IEC61000-4-2 level 4的标准。
5)ZK601_360通过一个柔性PCB板(16PINS)与外在系统相连,简单易用。

ZKW Eye 100H虹膜采集模组

上位机需求

1、Window系统的电脑 Windows 7 (32/64位)/Windows 8 (32/64位) / Windows 10 (32/64位):

– Microsoft Windows 7 (32-位) or Windows 7 (64-位)操作系统

– 512MB RAM (或者更高)

– x86处理器,2.0GHz(或者更高)

– 2GB或以上可用硬盘空间

– 专用USB2.0接口(或更高)

2、其他可选择的支持设备:

– 安卓设备  (ARM32/64位处理器,建议cortex A72以上, 内存1G以上)

– 嵌入式LINUX设备 (ARM32/64位处理器,建议Cortex A72以上, 内存1G以上)